null
RedNet D16R MkII

RedNet D16R MkII

(No reviews yet) Write a Review
$2,799.99
MSRP: $3,639.99
(You save $840.00 )
SKU:
AMS-REDNET-D16R-MKII
UPC:
815301001195
Availability:
Drop Ships from Manufacturer

RedNet D16R MkII

16x16 AES3 I/O With Independent Level Control

 

The RedNet D16R MkII is a 16-channel bi-directional AES3 interface for Dante® networks. The 1U rackmount device features individual input and output channel level controls, allowing for precise calibration and control of all input and output levels using RedNet Control. RedNet D16R MkII features power supply and Ethernet redundancy with auto switchover in case of failure.

 

Various connection options make RedNet D16R MkII a flexible addition to any Audio-over-IP system. A pair of DB25 multipin connectors each connect eight channels of AES3 I/O into and out of the interface, while XLR and RCA ports enable two-channel AES3 and S/PDIF connections, respectively, to be made.

 

Sample rate conversion on every input enables external equipment to operate at different sample rates, and DARS signals are accepted on the XLR connector. Word Clock I/O on BNC connectors allows synchronisation to house clock, or syncing external equipment to the Dante network.

 

 

 

16-channel bi-directional AES3 interface for Dante networks
Individual input and output channel level control using RedNet Control software
Power supply and Ethernet redundancy with auto switchover in case of failure
Sample rate conversion on all input channels
Two DB25 connectors with AES59 standard configuration; each carries eight channels of AES3 I/O
RCA connectors for two-channel S/PDIF input and output
XLR connectors for alternate AES3 I/O and DARS input
BNC connectors for Word Clock input and output
Remote routing and control using RedNet Control and Dante Controller
Full operability with Focusrite RedNet and Red interfaces, plus all Dante devices from hundreds of manufacturers

SPECIFICATIONS

INPUT / OUTPUT TRIM


 

Input Trim

-78 to 0dB in 1dB steps (per channel)

Output Trim

-78 to 0dB in 1dB steps (per channel)

INPUT SAMPLE RATE CONVERTORS


 

Sample Rate Range

32Hz to 214kHz

Gain Error

-0.3dB

Dynamic Range

Greater than 138dB (-60 dBFS method)

THD + N

Less than -130dB (0.00003%); 0 dBFS input

Latency

11 to 45 samples (network and input sample rate dependent)

DIGITAL PERFORMANCE


 

Supported Sample Rates

44.1 / 48 / 88.2 / 96 / 176.4 / 192 kHz (-4% / -0.1% / +0.1% / +4.167%) at 24 bit

Clock Sources

Internal, Word Clock, DARS, AES input 1-2, AES input 9-10 or from Dante Network Master

External Word Clock Range

Nominal sample rate ±7.5%

REAR PANEL CONNECTIVITY


 

AES/ EBU


 

Channel Count

2 x 2 S/PDIF Channels (reduces AES/EBU input channels)

Input And Output

2 x DB25 connectors (AES59 Combined I/O / Tascam Digital)

Alternate Input (Optional DARS)

1 x Female XLR (replaces DB25 channels 1-2)

Alternate Output

1 x Male XLR (duplicates DB25 channels 1-2)

S/PDIF


 

Channel Count

2 x 2 S/PDIF Channels (reduces AES/EBU input channels)

Input

1 x RCA phono socket (replaces DB25 channels 3-4)

Output

1 x RCA phono socket (switchable, duplicates any DB25 channel pair)

WORD CLOCK


 

Input

1 x BNC 75Ω port (switchable termination)

Output

1 x BNC 75Ω port

PSU & NETWORK CONNECTIONS


 

PSU

2 x Internal, 100-240V, 50/60Hz, consumption 30VA

Network

2 x EtherCON NE8FBH-S, also compatible with standard RJ45 connectors (Accomodates rugged EtherCON NE8MC*. Does not intermate with Cat 6 cable connector NE8MC6-MO and NKE65* cable)

FRONT PANEL INDICATORS


 

Primary PSU (A)

Green LED. Illuminates when an AC input is applied and all DC outputs are present

Secondary PSU (B)

Green LED. Illuminates when an AC input is applied and all DC outputs are present

Secondary Network

Green LED. Indicates that a network connection is present on secondary port when in redundant mode. Not used in switched mode

Network Locked

Green LED. When unit is following network grand master, shows valid network lock. When unit is network master, shows lock to indicated clock source. Flashing indicates external clock is selected but not connected

Sample Rate

Orange LED for each: 44.1kHz, 48kHz, x2, x4

Pull Up/Down

Orange LED. Indicates unit is set to operate on a Dante pull up/down domain

Signal Indicators

16 Green LEDs, 8 input/8 output indicators. Illuminate @ -126dBFS

Clock Source

Orange LED for each: Internal, Word Clock, DARS, Input 1–2 and Input 9–10

Primary Network

Green LED. Indicates that a network connection is present on primary port when in redundant mode. When in switched mode, a valid network connection at either primary or secondary network port will cause this LED to illuminate

NETWORK MODES


 

Redundant

Allows unit to connect to two independent networks

Switched

Connects both ports to integrated network switch allowing daisy-chaining of devices

DIMENSIONS


 

Height

44.5mm/ 1.75"

Width

482.6mm/ 19"

Depth

263mm/ 10.35"

WEIGHT


 

Weight

3.84kg

POWER


 

PSU

2 x Internal, 100-240V, 50/60Hz, consumption 30VA.

HEAT PERFORMANCE


 

Operating Temperature

Operates at up to an ambient temperature of 50 degrees Celcius